i drove out to ikea today and returned the 7 pieces of trim for above the cabinets. they're the last of the stuff i'd have to return before october 22. ikea gives you 365 days to return stuff.
i returned a drawer i'd picked up a replacement for the last time i went in. i changed out the same medium drawer front to the new taller/high sides drawer. i wanted the sides to come all the way up rather than just halfway like the medium height drawer sides do.
i also returned a set of shelves i picked up last time where i accidentally bought the 24" wide ones but i meant to get the 15" wide ones.
then i picked up 3 more pieces of the new bodkin trim pieces to go with the one piece i picked up last time. hopefully this will be the very last. we'll see.
Wednesday, October 9, 2019
Friday, August 30, 2019
kitchen update # 64 toe kicks
we worked on the toe kicks for the sink side cabinets. they were a bit tricky.
for the cabinet nearest the porch door, dad figured out that we could clip a little piece of the toe kick going sideways on the cabinets leg NEXT to this cabinet, and then cut the toe kick piece to butt up right against that. otherwise there would have been a gap between the toe kick under this cabinet and the back panel on the cabinet next to it. so we got that one in.
that short little piece on the inner corner under the cabinet is the one we had to find a way to secure. this is the before picture without it
looks good. still need to put the baseboard trim back on the right end.
then we worked on how to do the inside of the peninsula. because of the corner cabinet facing the dining room, the legs at the back of that cabinet did NOT line up with the legs on the front of the kitchen-facing peninsula cabinet. the toe kick would be at a funky angle.
so the piece wouldnt clip on right.
plus i had no more laminate flooring left, and there was a gap there if we snapped it to the legs as intended.
so dad screwed a 2x2 board into the subfloor right at the end of the laminate flooring, in front of the legs.
then we screwed the toekick to the 2x2 board. voila, gap in flooring covered, toe kick straight from left end to right end. win!
for the piece in front of the sink we just had to measure from that toe kick to the end of the sink cabinet and install that. easy peasy. if you look closely on under the peninsula cabinets (with the flashlight in it), you can see the screw we used to attach that toekick.
the dishwasher has a removable toekick panel and clearly states in the instructions NOT to cover it with any other toekick material. (or you block access to the plumbing and electrical and height/level adjustments). that toekick is black.
the last gap we had to work on was between the panel on the side of the dishwasher back to the dishwasher toekick.
same type of little front to back gap as with the corner cabinet by the porch door.
so we screwed a block of wood to the side of the bottom of the inner mounting board, and cut a piece of toekick that went from the panel back alongside the dishwasher to the back wall, and just sort of propped it in place. it works. and its not like anyone will ever kick that piece since its behind the panel and to the side of the dishwasher toekick.
thursday/yesterday i went to ikea and returned the 3 extra toekick pieces and 4 glass drawer sides that were extra. then i bought a new deeper 24" wide drawer and the deeper glass drawer sides for that. picked up a piece of bodkin fancier trim to try above the cabinets. i picked up a 30x5 drawer front i'd like to try over the stove since it'll have finished edges. it'll need to be cut shorter, but the ends will be finished, and no scratches. i also picked up another utrusta metal shelf divider thing for the cabinet over the fridge. and 2 trash can lids for the times when the garbage or recycles stink. the trash really stinks right now and isnt even half full so the lid is good. and when the lids are not needed i can stick them down between the two trash cans that are narrower at the bottom than the top.
i need to finish the trim between the cabinets and the ceiling, and i will be done with ikea stuff. there are extra of the trim pieces i'd previously chosen that would need to be returned before the 365 days are up end of october. and i seem to be moving a lot slower. i just want to finish that and not have to worry about returns or exchanges.
otherwise there is still the backsplash to be decided. and i have no clue what i want.
and there is one outlet i'd like to turn into a double outlet, which will require a new larger electrical box to fit two sets of outlets, and cutting into the sheetrock of the wall to remove the old box and install the new one. dad says we can do it. it'll require some sheetrock patching but i'm pretty good at that now and i have some leftover sheetrock.
then the kitchen will be done! its been 10 months. i dont at all mind how long its taken to get this far. i really really REALLY appreciated being able to do this at our own pace. to be able to take our time to solve problems we ran into rather than having to hurry thru and half-ass something. and it helped that we finished one half before we started on the other so i always at least had half a kitchen. and we managed to jury-rig up the old kitchen sink on top of the new cabinets until the new counters and new sink got installed. so i only had a few days of having to do dishes in the bathroom.
for the cabinet nearest the porch door, dad figured out that we could clip a little piece of the toe kick going sideways on the cabinets leg NEXT to this cabinet, and then cut the toe kick piece to butt up right against that. otherwise there would have been a gap between the toe kick under this cabinet and the back panel on the cabinet next to it. so we got that one in.
that short little piece on the inner corner under the cabinet is the one we had to find a way to secure. this is the before picture without it
looks good. still need to put the baseboard trim back on the right end.
then we worked on how to do the inside of the peninsula. because of the corner cabinet facing the dining room, the legs at the back of that cabinet did NOT line up with the legs on the front of the kitchen-facing peninsula cabinet. the toe kick would be at a funky angle.
so the piece wouldnt clip on right.
plus i had no more laminate flooring left, and there was a gap there if we snapped it to the legs as intended.
so dad screwed a 2x2 board into the subfloor right at the end of the laminate flooring, in front of the legs.
then we screwed the toekick to the 2x2 board. voila, gap in flooring covered, toe kick straight from left end to right end. win!
for the piece in front of the sink we just had to measure from that toe kick to the end of the sink cabinet and install that. easy peasy. if you look closely on under the peninsula cabinets (with the flashlight in it), you can see the screw we used to attach that toekick.
the dishwasher has a removable toekick panel and clearly states in the instructions NOT to cover it with any other toekick material. (or you block access to the plumbing and electrical and height/level adjustments). that toekick is black.
the last gap we had to work on was between the panel on the side of the dishwasher back to the dishwasher toekick.
same type of little front to back gap as with the corner cabinet by the porch door. so we screwed a block of wood to the side of the bottom of the inner mounting board, and cut a piece of toekick that went from the panel back alongside the dishwasher to the back wall, and just sort of propped it in place. it works. and its not like anyone will ever kick that piece since its behind the panel and to the side of the dishwasher toekick.
thursday/yesterday i went to ikea and returned the 3 extra toekick pieces and 4 glass drawer sides that were extra. then i bought a new deeper 24" wide drawer and the deeper glass drawer sides for that. picked up a piece of bodkin fancier trim to try above the cabinets. i picked up a 30x5 drawer front i'd like to try over the stove since it'll have finished edges. it'll need to be cut shorter, but the ends will be finished, and no scratches. i also picked up another utrusta metal shelf divider thing for the cabinet over the fridge. and 2 trash can lids for the times when the garbage or recycles stink. the trash really stinks right now and isnt even half full so the lid is good. and when the lids are not needed i can stick them down between the two trash cans that are narrower at the bottom than the top.
i need to finish the trim between the cabinets and the ceiling, and i will be done with ikea stuff. there are extra of the trim pieces i'd previously chosen that would need to be returned before the 365 days are up end of october. and i seem to be moving a lot slower. i just want to finish that and not have to worry about returns or exchanges.
otherwise there is still the backsplash to be decided. and i have no clue what i want.
and there is one outlet i'd like to turn into a double outlet, which will require a new larger electrical box to fit two sets of outlets, and cutting into the sheetrock of the wall to remove the old box and install the new one. dad says we can do it. it'll require some sheetrock patching but i'm pretty good at that now and i have some leftover sheetrock.
then the kitchen will be done! its been 10 months. i dont at all mind how long its taken to get this far. i really really REALLY appreciated being able to do this at our own pace. to be able to take our time to solve problems we ran into rather than having to hurry thru and half-ass something. and it helped that we finished one half before we started on the other so i always at least had half a kitchen. and we managed to jury-rig up the old kitchen sink on top of the new cabinets until the new counters and new sink got installed. so i only had a few days of having to do dishes in the bathroom.
Tuesday, August 27, 2019
kitchen update # 63 - window trim
dad came up and we whipped out the trim for the inside of the kitchen window.
the window before trim
the trim laid out on the kitchen table so we could nail the corners together before we put it in place. because of the cabinets and sink theres no way to nail the corners together once its in place.
the blue arrow shows the teeny little nail pounded partway in. we predrilled the hole with a smaller drillbit to help prevent fracturing the skinny trim.
we also glued the corners together
tada! window trim in place. you can see how there wouldnt have been room to reach the corners to nail.
i fucked up pounding one of the nails in and bent it over. i had to pull it out and try again. the second hole i drilled managed to line up exactly with a nail holding the sheetrock underneath to the studs in the wall behind it. so of course that nail wouldnt pound in at all. third times the charm, ugh. i dont know if wood filler will work on plastic/polystyrene trim. i went with this trim because its over the sink and will get splashed and i dont want it to rot. the new kitchen window is plastic/vinyl and wont rot either.
but the window trim is done! still needs caulking though.
the window before trim
the trim laid out on the kitchen table so we could nail the corners together before we put it in place. because of the cabinets and sink theres no way to nail the corners together once its in place.
the blue arrow shows the teeny little nail pounded partway in. we predrilled the hole with a smaller drillbit to help prevent fracturing the skinny trim.
we also glued the corners together
tada! window trim in place. you can see how there wouldnt have been room to reach the corners to nail.
i fucked up pounding one of the nails in and bent it over. i had to pull it out and try again. the second hole i drilled managed to line up exactly with a nail holding the sheetrock underneath to the studs in the wall behind it. so of course that nail wouldnt pound in at all. third times the charm, ugh. i dont know if wood filler will work on plastic/polystyrene trim. i went with this trim because its over the sink and will get splashed and i dont want it to rot. the new kitchen window is plastic/vinyl and wont rot either.
but the window trim is done! still needs caulking though.
Saturday, August 17, 2019
kitchen update # 62 - cutting the tall cabinet down
the old tall kitchen cabinet shown here was one solid piece. unfortunately it was 2 inches (5cm) too tall for the basement ceiling, even after the decorative trim on top was removed.
i cut the top half off from the bottom half with the oscillating tool by cutting along the flat top of the bottom section in the microwave hole. that way i got a nice straight edge.
(and all those boxes in the background FINALLY made it into the recycling bin now that the bazillions of cabinet boxes are all gone)
this lower half of the cupboard has a normal bottom with the recessed toe-kick (ignore the dirt from sitting out in the garage for the better part of a year)
here is the top half, turned upside down, needing the microwave-hole-sides cut off. but not cut ALL the way off or it'd be too short to fit next to the other base cabinets.
dad came out with his skilsaw and we measured and marked and cut most of those microwave-space-sides off. dad could get the straight line with his saw that i couldnt get with mine.
here is the top half all cut down. we'll make some more minor cuts on the bottom so it can have a proper toe-kick like the other cabinets.
and i'll take off the doors and flip them around so the handles are on top instead of the bottom. i already measured and the hinges are perfectly equal so it'll be an easy switch.
the top side of this top-half of the tall cabinet isnt nice and smooth. the decorative trim on the top, some of the screws were glued in and would not unscrew. dad had to pound it off.
another challenge is this cabinet (top half and bottom half) has no back. all the other cabinets had backs. so we'll have to cut something up to fit. eventually.
these cabinets will be repurposed into a better kitchen for the roommate in the basement, but after all the work we did, we're taking some time off before starting that project.
i cut the top half off from the bottom half with the oscillating tool by cutting along the flat top of the bottom section in the microwave hole. that way i got a nice straight edge.
(and all those boxes in the background FINALLY made it into the recycling bin now that the bazillions of cabinet boxes are all gone)
this lower half of the cupboard has a normal bottom with the recessed toe-kick (ignore the dirt from sitting out in the garage for the better part of a year)
here is the top half, turned upside down, needing the microwave-hole-sides cut off. but not cut ALL the way off or it'd be too short to fit next to the other base cabinets.
dad came out with his skilsaw and we measured and marked and cut most of those microwave-space-sides off. dad could get the straight line with his saw that i couldnt get with mine.
here is the top half all cut down. we'll make some more minor cuts on the bottom so it can have a proper toe-kick like the other cabinets.
and i'll take off the doors and flip them around so the handles are on top instead of the bottom. i already measured and the hinges are perfectly equal so it'll be an easy switch.
the top side of this top-half of the tall cabinet isnt nice and smooth. the decorative trim on the top, some of the screws were glued in and would not unscrew. dad had to pound it off.
another challenge is this cabinet (top half and bottom half) has no back. all the other cabinets had backs. so we'll have to cut something up to fit. eventually.
these cabinets will be repurposed into a better kitchen for the roommate in the basement, but after all the work we did, we're taking some time off before starting that project.
Wednesday, August 14, 2019
kitchen update # 61 - day after the countertops
on august 7 i had the roommate shut off the main water to the house so i could replace the shut off valves under the sink. (the shut off valve is down in his bathroom).
installing the new faucet
new faucet with the pull-down sprayer head in place
lots of hoses, all fit thru one hole in the countertop
underneath
the old shut off valves, the one on the left (hot water) leaks and has a paper towel shoved in it.
then i used dads pipe cutter and cut off the old leaking shut off valves
dads pipe cutter (the red thing). you twist the dial on the side to tighten the cutter wheel and spin it around the pipe, then tighten, then spin, and keep doing it until the pipe breaks off.
the orange thing has two functions. one is those little black circles in the middle are metal cutters that strip any burrs off the top of the pipe after the pipe has been cut off. you spin it around while pressing down. the second function is that it tells you the proper depth for the push-to-fit valve to be pushed down to.
you draw a line under it, then push and push and push the valve all the way down so its properly in place.
voila! valve pressed down to the line, perfect fit. no soldering.
then i attached the hoses from the faucet to the new shut off valves
lovely functional shut off valves under the kitchen sink, and they work nice. then i had the roommate turn the water back on and no leaks.
then i needed to make a run to the store for more plumbing parts because the sink drains are in different spots than the old ones, so the old drain pipe pieces didnt work. i put a bowl in the sink under the faucet to remind me theres no drain hooked up yet even though the water is hooked up.
on august 8 i went to menards and found all the new plumbing parts i needed in one set.
i attached the little stubs to the sink strainer, then screwed the sink strainer in with the plumbers putty.
view from above with the new sink strainer in place
all the plumbing drain pieces cut and screwed together! no leaks!
kitchen with the sink cabinet doors in place now that i'm done with all the plumbing underneath.
the new faucet is great, but at first kept dripping a few times each time i shut it off. i worried if thats just how the pull-down sprayer faucets work or if i didnt something wrong. but it quit doing that.
every time i walk into or out of the kitchen i drag my hands over the new pretty counters.
installing the new faucet
new faucet with the pull-down sprayer head in place
lots of hoses, all fit thru one hole in the countertop
underneath
the old shut off valves, the one on the left (hot water) leaks and has a paper towel shoved in it.
then i used dads pipe cutter and cut off the old leaking shut off valves
dads pipe cutter (the red thing). you twist the dial on the side to tighten the cutter wheel and spin it around the pipe, then tighten, then spin, and keep doing it until the pipe breaks off.
the orange thing has two functions. one is those little black circles in the middle are metal cutters that strip any burrs off the top of the pipe after the pipe has been cut off. you spin it around while pressing down. the second function is that it tells you the proper depth for the push-to-fit valve to be pushed down to.
you draw a line under it, then push and push and push the valve all the way down so its properly in place.
voila! valve pressed down to the line, perfect fit. no soldering.
then i attached the hoses from the faucet to the new shut off valves
lovely functional shut off valves under the kitchen sink, and they work nice. then i had the roommate turn the water back on and no leaks.
then i needed to make a run to the store for more plumbing parts because the sink drains are in different spots than the old ones, so the old drain pipe pieces didnt work. i put a bowl in the sink under the faucet to remind me theres no drain hooked up yet even though the water is hooked up.
on august 8 i went to menards and found all the new plumbing parts i needed in one set.
i attached the little stubs to the sink strainer, then screwed the sink strainer in with the plumbers putty.
view from above with the new sink strainer in place
all the plumbing drain pieces cut and screwed together! no leaks!
kitchen with the sink cabinet doors in place now that i'm done with all the plumbing underneath.
the new faucet is great, but at first kept dripping a few times each time i shut it off. i worried if thats just how the pull-down sprayer faucets work or if i didnt something wrong. but it quit doing that.
every time i walk into or out of the kitchen i drag my hands over the new pretty counters.
Tuesday, August 13, 2019
kitchen update # 60 - countertops are in!
on august 6 they came out and installed the countertops. again they called and asked if they could come early. it was two hispanic guys speaking in spanish to each other the whole time. heidi got another peanut butter stuffed frozen kong that kept her happily occupied. it took about 2 hours. they had to do some cutting with the backsplash pieces.
they carried in the first two slabs on either side of the stove
the slab for the peninsula
unloading the last section from the truck
the sink slab in and the backsplash pieces cut
after sneaking those pictures i left them in peace so they could attach the counters to the cabinets. look look i have counters!
and they're not yellow! (the old ones were harvest gold yellow)
love my new kitchen!
the pattern on the counters
my new extra deep undermount sink
i couldnt attach the plumbing or the new faucet until 24 hours have passed so the adhesive can properly set
they attached a metal strip to the underside of the counter above the dishwasher for the dishwasher to mount to, since you cant screw into the quartz
the propped it up with a couple shims on the top of the dishwasher door
extra deep sink, thats my elbow! its deeper than i expected.
rounded corners on the peninsula
some things look weird or feel weird so i'm going to give it some time first before deciding if theres a problem or if weird is just new and different and is fine once i get used to it.
they carried in the first two slabs on either side of the stove
the slab for the peninsula
unloading the last section from the truck
the sink slab in and the backsplash pieces cut
after sneaking those pictures i left them in peace so they could attach the counters to the cabinets. look look i have counters!
and they're not yellow! (the old ones were harvest gold yellow)
love my new kitchen!
the pattern on the counters
my new extra deep undermount sink
i couldnt attach the plumbing or the new faucet until 24 hours have passed so the adhesive can properly set
they attached a metal strip to the underside of the counter above the dishwasher for the dishwasher to mount to, since you cant screw into the quartz
the propped it up with a couple shims on the top of the dishwasher door
extra deep sink, thats my elbow! its deeper than i expected.
rounded corners on the peninsula
some things look weird or feel weird so i'm going to give it some time first before deciding if theres a problem or if weird is just new and different and is fine once i get used to it.
Subscribe to:
Posts (Atom)